Diseño y construcción de una máquina dobladora de tubos hidráulica con accionamiento automático

Para citar o enlazar este item, por favor use el siguiente identificador: http://dspace.ups.edu.ec/handle/123456789/5995
Título : Diseño y construcción de una máquina dobladora de tubos hidráulica con accionamiento automático
Autor : Moreno Flores, Giovanny Patricio
Director de Tesis: Obando Herrera, Fabio Eduardo
Resumen traducido: The main objective of this work is to design and build a hydraulic tube bending machine with automatic activation. Chapter I: Theoretical framework, general information is collected for the process and procedure of tube bending, bending the different methods with their particular characteristics, in addition to the mechanical system, hydraulic and electrical that can intervene in a hydraulic pipe bending machine. For each system will be a brief description of their respective elements. Chapter II: STUDY AND SELECTION OF ALTERNATIVES, description will be made of three alternatives, each will be detailed in their advantages and disadvantages, with the information obtained will be an analysis table where you compare and evaluate the proposed alternatives, the option that meets the characteristics and requirements requested by the sponsor will be the selected alternative for the design and construction of the machine. Chapter III: DETERMINATION OF FORCE IN THE BENT, in this chapter is will be made an analysis of the loads that influence the bending, the same that will be the reference for the calculation and selection of the elements of the mechanical system and hydraulic system. With the system power demand will select the elements that make up the electrical control system. Chapter IV: COSTS, will be analyzed the direct and indirect costs that directly influence the real value that will have the construction of the machine, in direct costs will detail the cost of materials, equipment, labor, use of machinery and equipment, in indirect costs give you a percentage of the total direct costs for both contingencies that arise at the time of construction and also will take into account the engineering (design) that was used to development the project. Chapter V: CONSTRUCTION AND ASSEMBLY, in this chapter will detail the construction and installation of the elements and accessories mechanical, hydraulic and electrical that will make up the machine Chapter VI: Conclusions and recommendations, in this chapter summarized the results of research in addition to compliance the goals set at the beginning of the project, in based on the conclusions raised, raises the most appropriate recommendations. For system design, machine assembly, 3D modeling and projection of planes was made in the program Autodesk Inventor 2013. The advantage of using this program is the animation of moving parts and the visualization of the machine in three dimensions.
Resumen : El objetivo principal del presente trabajo es diseñar y construir una máquina dobladora de tubos hidráulica con accionamiento automático. Capítulo I: MARCO TEÓRICO, se recopila la información general correspondiente al proceso y procedimiento del doblado de tubos, los diferentes métodos de doblado con sus características particulares, además del sistema mecánico, hidráulico y eléctrico que pueden intervenir en una máquina dobladora hidráulica de tubos. Para cada sistema se realizará una breve descripción de sus respectivos elementos. Capítulo II: ESTUDIO Y SELECCIÓN DE ALTERNATIVAS, se realizará la descripción de tres alternativas, en cada una se detallará sus ventajas y desventajas, con la información obtenida se realizará una tabla de análisis donde se comparará y valorará las alternativas propuestas, la opción que cumpla las características y requerimientos solicitados por el auspiciante será la alternativa seleccionada para el diseño y construcción de la máquina. Capítulo III: DETERMINACIÓN DE LA FUERZA EN EL CURVADO, en este capítulo se realizará un análisis de las cargas que influyen en el curvado, las mismas que serán la referencia para el cálculo y selección de los elementos que constituyen el sistema mecánico y sistema hidráulico. Con la potencia demandada por sistema se procederá a la selección de los elementos que conformarán el sistema de control eléctrico. Capítulo IV: COSTOS, se analizarán los costos directos e indirectos que influyen directamente en el valor real que tendrá la construcción de la máquina, en los costos directos se detallará el costo por materiales, accesorios, mano de obra, empleo de maquinaria y equipos, en los costos indirectos se dará un porcentaje del total de los costos directos tanto para los imprevistos que surgen al momento de la construcción como también se tomará en cuenta la ingeniería (diseño) que se empleó para el desarrollo del proyecto. vii Capítulo V: CONSTRUCCIÓN Y MONTAJE, en este capítulo se detallará la construcción y montaje de los elementos y accesorios mecánicos, hidráulicos y eléctricos que conformarán la máquina. Capítulo VI: CONCLUSIONES Y RECOMENDACIONES, en este capítulo se resumen los resultados de la investigación además del cumplimiento de los objetivos planteados al comienzo del proyecto, en base a las conclusiones planteadas se realizan las recomendaciones que más lo ameriten. Para el diseño de sistema, el ensamble de la máquina, el modelado en 3D y la proyección de planos se realizó en el programa Autodesk Inventor versión 2013. La ventaja que presenta el empleo de este programa es la animación de las partes móviles y la visualización de la máquina en tres dimensiones.
Palabras clave : INGENIERÍA MECÁNICA
DISEÑO EN INGENIERÍA
MÁQUINAS HIDRÁULICAS
AUTOMATIZACIÓN
DOBLADO DE TUBERÍAS
Fecha de publicación : ago-2013
URI : https://dspace.ups.edu.ec/handle/123456789/5995
Idioma: spa
Pertenece a las colecciones: Grado

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
UPS - ST004755.pdfTexto completo2,28 MBAdobe PDFVisualizar/Abrir


Este ítem está sujeto a una licencia Creative Commons Licencia Creative Commons Creative Commons